Foxboro by Schneider Electric

De 84CS serie vortex massaflowmeter met sanitaire aansluiting voor de farmeceutische en voedingsmiddelenindustrie is een aanvulling op de Schneider Electric (voorheen Foxboro) familie van intelligente, krachtige vortex flowmeters. De 84CS serie is verkrijgbaar met 4 tot 20 mA, HART7 en of Modbus communicatie en kan optioneel worden uitgerust met temperatuurcompensatie voor massaflowmeting va...

The Foxboro 43AP pneumatic controller is a versatile process instrument controller that can be used to control pressure, temperature, flow and level. As with all process controllers, the Foxboro 43AP pneumatic controller continuously detects the difference between a process measurement and its set point.

The Foxboro Model 11GM Transmitters accurately measure gauge pressure and transmit a proportional pneumatic output signal to receivers which may be several hundred meters or yards away.

The CFS300A is the cost effective solution for accurate measurement for a variety of applications. The CFS300A reliably measures mass, density, volume, temperature, volume concentration or solid content. Dual-straight tube with optimized flow splitter, for general purpose applications and process control. End connections available for ½” (DN15) to 4” (DN100).

The IAP05S series is a budget-friendly pressure transmitter within the Schneider Electric range and is standard SIL2 certified. The IAP05S measures an absolute pressure with an accuracy of 0.075% of the chosen measuring range, varying from 50 kPa to 345 bar. This makes the IAP05S pressure transmitter somewhat less accurate than its bigger brothers, but also a lot cheaper. For less demanding app...

The IAP10S series is a very robust and advanced pressure transmitter within the Schneider Electric range and is SIL2 certified as standard. The IAP10S measures an absolute pressure with an accuracy of 0.05% of the reading. Thanks to the special FoxCal technology, one transmitter has no less than 11 calibration curves in a pressure range of 0-414 bar. This allows the same model of pressure trans...

The IAP50S series is a very robust and extremely accurate pressure transmitter within the Schneider Electric range and is SIL2 certified as standard. The IAP50S measures an absolute pressure with an accuracy of 0.025% of the reading. Thanks to the special FoxCal technology, one transmitter has no less than 11 calibration curves in a pressure range of 0-414 bar. This allows the same model IAP50S...

The IDP05S series is a budget-friendly differential pressure transmitter within the Schneider Electric range with standard SIL2 certification. The IDP05S measures a pressure difference with an accuracy of 0.075% of the chosen measuring range, ranging from 50 kPa to 207 bar. This makes the IDP05S differential pressure transmitter less accurate than its bigger brothers, but also a lot cheaper. Fo...

The IDP10S series is a very robust and advanced differential pressure transmitter within the Schneider Electric range and is SIL2 certified as standard. The IDP10S measures a pressure difference with an accuracy of 0.05% of the reading. Thanks to the special FoxCal technology, one transmitter has no less than 11 calibration curves in a pressure range of 0-414 bar. This allows the same model of...

The IDP50S series is a very robust and extremely accurate differential pressure transmitter within the Schneider Electric range and is SIL2 certified as standard. The IDP50S measures a pressure difference with an accuracy of 0.025% of the reading. Thanks to the special FoxCal technology, one transmitter has no less than 11 calibration curves in a pressure range of 0-414 bar. This allows the sam...

The IGP05S series is a budget-friendly pressure transmitter within the Schneider Electric range and is standard SIL2 certified. The IGP05S measures a relative pressure with an accuracy of 0.075% of the selected measuring range, ranging from 50 kPa to 345 bar. This makes the IGP05S pressure transmitter less accurate than its bigger brothers, but also a lot cheaper. For less demanding application...

The IGP10S series is a very robust and advanced pressure transmitter within the Schneider Electric range and is SIL2 certified as standard. The IGP10S measures a relative pressure with an accuracy of 0.05% of the reading. Thanks to the special FoxCal technology, one transmitter has no less than 11 calibration curves in a pressure range of 0-414 bar. This allows the same model of pressure transm...

The IGP50S series is a very robust and extremely accurate gauge pressure transmitter within the Schneider Electric range and is SIL2 certified as standard. The IGP50S measures a relative pressure with an accuracy of 0.025% of the reading. Thanks to the special FoxCal technology, one transmitter has no less than 11 calibration curves in a pressure range of 0-414 bar. This allows the same model...

The Foxboro RTT15S temperature transmitter is a temperature transmitter that uses HART communication. The RTT15S is available with many types of housing, sensor types and many other options making it suitable for most temperature applications. The transmitter can be configured without interrupting the process. The optional display has a red or white backlight. The display can also be used for d...

The CFS400A has been developed to meet the demanding custody transfer requirements of the oil and gas industry and is well suited to bulk measurement in many applications. The option of Super Duplex (UNS S32760) provides a maximum operating pressure of 180 barg. A high level of performance makes the CFS400A suitable for the bulk measurement of petroleum and oil as well as products like syrup, m...

The CFS700A is the only sensor for mass flow with a single straight measuring tube that is available in Titanium, Stainless Steel, Hastelloy® or Tantalum. Single straight tube without flow splitter for lowest pressure drop, for advanced applications and harsh environments. End connections available for ½” (DN15) to 4” (DN100).

The CFT34A Coriolis mass flow transmitter will provide the highest performance possible across a wide range of applications. For the measurement of liquids or gases, cryogenic to high temperature fluids, single or multi-phase fluids and advanced digital signal processing techniques is used to give accurate measurements of mass flow, density and temperature. It is developed according to IEC 615...

The wireless WAP10 absolute pressure sensors measure the pressure of various industrial processes and transmit them wirelessly to a central collector (WCC10). This sends the values from multiple sensors via WirelessHART to any central system. There are versions with pressure ranges up to 2.1 bar absolute. The field sensors are explosion-proof according to ATEX and Canadian and American guidelines.

With the WCC10 central collector from Schneider Electric, the data from 8 wireless IAN field sensors can be collected. There are field sensors for measuring temperature, pressure and differential pressure. Communication between the field sensors and the WCC10 is via Bluetooth and can be fully configured with an app via WiFi. This makes the system very flexible and very easy to install. In addit...

The wireless WDP10 differential pressure sensors measure the differential pressure of various industrial processes and transmit them wirelessly to a central collector (WCC10). This sends the values from multiple sensors via WirelessHART to any central system. There are versions with differential pressure ranges up to 500 mbar, 2.1 bar or 21 bar. The field sensors are explosion-proof according t...

The wireless WGP10 relative pressure sensors measure the pressure of various industrial processes and transmit them wirelessly to a central collector (WCC10). This sends the values from multiple sensors via WirelessHART to any central system. There are versions with pressure ranges up to 2.1, 21 or 70 bar. The field sensors are explosion-proof according to ATEX and Canadian and American guideli...

The wireless WRT10 temperature sensors measure the temperature of various industrial processes and send them wirelessly to a central collector (WCC10). This sends the values from multiple sensors via WirelessHART to any central system. There are RTD and thermocouple versions from -200 to + 885 ° C with various insertion lengths between 50 and 400 mm. Optionally, thermowells in various lengths c...

De Schneider electric 8400A serie magnetische flowbuis vormt samen met de IMT serie transmitters een economische flowmeter met wafer-aansluiting. De 8400A magnetische flowmeters zijn beschikbaar in maten van DN10 tot DN150 voor licht industriële toepassingen tegen een scherpe prijs. Voor een hogere nauwkeurigheid en chemische bestendigheid adviseren wij de 8500A serie.

The IP26 (current to pressure) transducer converts a 4–20mA electrical current signal to a proportional linear pneumatic output. The unique conversion technology provides a high level of accuracy and repeatability for the operation of actuated valves. A low mass control circuit provides consistent output in high vibration applications. This compact unit is housed in an explosion proof enclosure...